收藏本页 | 设为主页 | 随便看看 | 手机版

上海长磐电子科技有限公司

站内搜索
 
产品分类
联系方式
  • 联系人:张咫萦
  • 电话:13916399810
  • 邮件:peter@champion.sh.cn
  • 手机:13916399810
新闻中心
您当前的位置:首页 » 供应产品 » SMA 600 剪脚成型机
SMA 600 剪脚成型机
点击图片查看原图
产品: 浏览次数:25SMA 600 剪脚成型机 
品牌: WERESCH
单价: 面议
最小起订量:
供货总量:
发货期限: 自买家付款之日起 天内发货
有效期至: 长期有效
最后更新: 2022-06-24 15:08
  询价
详细信息
Universal cutting, bending and beading machine for belted components with axial leads
Characteristics
Lead diameters from 0.4 to 1.3 mm without tool changes
Belt spacing 5, 10 and 15 mm
Output adjustable up to max. 8,000 units/hour (depends on belt quality and lead diameter)
Components are always tension released during processing (4-5 kg elastic)
Safe and strain-free handling of the components by bending rolls with adjustable pressure
Crimping deepness continuously adjustable
Bending angle also adjustable
Pitch (2,5 - 60 mm) and pin length (3 - 30 mm) can be read and continuously adjusted over a digital display
Parameters and belt width are adjustable with turning knobs (located outside the machine)
Repetitive accuracy of parameters 0.05 mm
Machine is PLC-controlled (Siemens) and switches off automatically under the following conditions: nominal pieces reached, end of or failure in belt
Electronic counter
Tools are driven by cam discs
Electric drive with tooth belt (three-phase motor)
Machine is very low-maintenance, since linear guides are located at flexible components (feed unit, bending unit, tension release, belt feeding)
Belt feeding takes place at the front of the machine
End of belt slides out at the back side of the machine
Components dro into ESD-box below the machine
Operation voltage: 230V/50Hz (standard), other voltages are available on demand
Length x width x height (without accessories): 600 x 500 x 510 mm
Weight: approx. 53 kg (without accessories)
 
Easy changeable tools (2-3 min) facilitate the production of the below mentioned standard forms
Special shapes are also possible
Tools are made with carbide to guarantee high durability
Tools illustration:
Bending form 1:
Cutting and bending from 0.4 - 1.3 mm wire diameters
Body diameter: max. 35 mm
With a printed board thickness of 1.6 mm, the lead penetration depth is then 1.5 0.1 mm (standard).
Distance between body and bending radius depends on width of the used bending finger
Options: 1.0 1.2 1.5 mm (standard = 1.5 mm)
Bending form 2:
Snap-in cutting, bending and crimping
Wire diameters from 0.4 - 0.9 mm
Body diameter: max. 35 mm
With a printed board thickness of 1.6 mm, the lead penetration depth is then 1.5 0.1 mm (standard).
Bending form 3:
Standoff cutting, bending and crimping
Wire diameters from 0.4 - 1.3 mm
Body diameter: max. 35 mm
With a printed board thickness of 1.6 mm, the lead penetration depth is then 1.5 0.1 mm (standard).
Bending form 4:
Upright / Crimping shapes: snap-in, standoff and straight cutting
Wire diameters from 0.4 - 0.9 mm without tool change
Body diameter: max. 5 mm
With a printed board thickness of 1.6 mm, the lead penetration depth is then 1.5 0.1 mm (standard).

询价单